Photos from the "light speed" display set up. Very difficult to get good clear photos but a lovely display. These were taken at the Sydney Exhibition at the Power House Museum Sydney June 2019.
Star wars original props and costumes as displayed at the Power House Museum Sydney, Australia June 2019
Built the basic, truncated octahedron's, for the model. CNC routing of MDF, assembled by hand with spruce strip edging.
I have ordered the square and triangular up-stands from Cut Laser Cut, too much to route and too dusty.
Looking good, will get the assembly with the up-stands complete and then epoxy tissue to seal.
After being given a load of 6mm think A5 sized MDF sheets I decided to cut the hex and squares to build a "fuel pod" at studio scale from the Valley Forge, Silent Running.
The cut edges are chamfered to a close edge and glued. On the inside I have taped and epoxied the joins, a strong basic geodesic box.
The raised edges are 1.5mm thick spruce, wood glued in place. The corners will need filler since I couldn't get another width to keep the same edge width on two sides. The square edges other hang to be sanded back and become a little thinner - I think this is as per the studio model but that is difficult to tell. The best referance comes from Lunadude and only a single referance dimension is shown.
I will skin with glass fibre tissue and epoxy, that will hide all sins, bits of filler and make a strong box that should resist delaminating or exposure to moisture / movement.
Got some time on the CAD to design some new 6mm scale gaming terrain / scatter terrain. A couple of storage receiver / chemical tank type things and a small terraforming building with a nice big fan on the roof.
Available on my Shapeways but I will get going on my B9Creator.
Finished the second spine for the 44" Eagle. Was a bit gutted to have to buy a length of 3/16" tube for just one diagonal, that was all I was short. All of it made from spare material otherwise. Gladly, I believe it is sold already and that will fund some more of the main build.
I took the opportunity to fill and start to remove the seams on the Airfix Kits and work on teh big command module for the 44" Eagle.
The command Module id a Chris Trice Glass Fiber component (top of the line, the best you can get) and came to me partially assembled. The two halves were not very well joined (strength) but were well aligned. I did a quick re-fix and then used some epoxy and tape on the inside to make a strong fix.
A quick coat of primer after a soapy rub down to prepare the surface.
My Airfix models and Command Module are filled across the seams with Vallejo Plastic Putty. I will leave them for a day or two so that any shrinkage can occur before I rub them down.
Might as well doing something hot whilst it is cold.......
A raw brass 44" Eagle Spine so far made from the spares box (and I still have loads of spare fish mouthed bit left, but not enough to make anything else).
The spine so far, included about £100's worth of material. With luck someone thinks I have added some value to this, I will put it up on eBay.
It has come out really nice so far, flat and straight, just one or two tube to adjust the line of but looking ok.
I will definitely add the angled ends before offering for sale and will consider adding the 3/32" diagonals, I will check to see what material I have left over.
I am adding the diagonals, the end sloped pieces and have cleaned up a little before finishing. Just waiting on some extra small diameter brass tube now. Looking good and will definitely be up for sale.
So, I went to Telford IPMS Scale Model World a couple of weeks ago......wow, quite an eye opener. A few Eagles (Round 2, small ones 1/48 scale). Quite an inspiration as well. I ended up buying a couple of kits. Some of my favourite, shiny silver coloured jets that fought based old fashioned dog fighting tactics with unguided weapons.
I purchased some Vallejo gloss black primer and their Silver Darts paint kit.
I am revisiting my own design of 1/72 Star Wars models, the Tie Scimitar and Crawler Tank.
All small enough to work on in the house during the colder winter months.
I am even talking to someone about kiting my Star Wars models, that will be interesting to follow up
A better attempt at painting the Eagle Frame and Spine. Good enough for me, for the time being. I am happy with the pale grey and happy with the overall effect. The finish could be better but I quite like the the rough and the lumps and bumps, kind of used looking. I am sure the original film model was a bit rough around the edges and I guess that gave something of interest in the finished filming, that is my story anyway.
I struggle with this painting business, this must be my 5th attempt at the dark grey details on the cages and spine. Keep trying. I wasn't too impressed with my work again, too dark and patchy. Awaiting on some white paint to tone down the grey, will try to build up the colour lightly and from a distance to get a thin over colour (not sure how to describe the effect we are trying for.
âThe masking is time consuming but I think it is what I am after. We will see.
Elsewhere I machined a few brass tubes to help with someone else's build. Got the CNC router going.
I have done little on the Eagle. Bored, bored of the 22's, the weaponised Eagles, the postal Eagle, the junk re imagined stuff, the armoured Eagles and the crap mash up Eagles with different Sci-Fi genres. Bored of all of the same questions, "is that a Gemini part?". I have loved the Eagle for 40 years, everyone has one now, a mass produced quick fix for muggles (there you go, Sci-Fi / Fantasy mash up).
I think I am getting over myself, I have left most of the 1999 / Eagle groups and forums, and will just come here to talk to myself.
I bought an airbrush, it is great. I have never used one before, like most of this, I have never done it before. Am I great with an airbrush? No, am I happy? Yes, this is great, I can get better at this and the result is already better than my attempt with a brush. Bull in a china shop; did I practice? No. Just have a go, the fun is coming back.
I have one spare with ear moulding on eBay (now sold).
If anyone would like one, I can make to order. I have One spare Ear Moulding.
Just let me know. Thanks.
Couple of images from the internet.
I haven't been around for a while. I have been doing some bits and pieces of modelling but an unintended break seemed to happen for no apparent reason.
I have a massive collection of data for war gaming and sci-fi modelling and have been wondering what to do with it.
I have signed up to Patron, a great place where creative types can get a bit of support and where collectively this can be meaningful. For me it will be a way of sharing data at very little cost to individuals but might make something to cover my efforts.
Have a look, I am offering two levels of support, one at $2 and the other at $5. At the $5 level, I will offer CAD data at my Battletech Longbow and Star Wars Tie Scimitar level. I will get on and finish my Star Wars Tie Tank and offer that.
Feel free to let me know what you think.
I purchased a few books of interest, sacred geometry, golden section, and one on compass and ruler exercises.
I really love the sacred geometry styled Gothic church windows. I have designed some in CAD and shall print some off with the hope that they make nice details for MDF type laser cut buildings for war gaming.
Also available on my Shapeways shop.
Here's one to look at; set of 4 windows works out as a good price.
A simple CNC program fairly quickly produced 3 sets of 44" Eagle Transporter landing pod feet from an A3 sized sheet of Perspex.
The sizes were spot on to the plans and the chamfered corners just marked out and cut with a file / sanding paper on a block.